UHF Bulkhead Female Angled Solder Type For Panel Mount

UHF Bulkhead Female Angled Solder Type For Panel Mount Specification

Core Number
Single core

Tensile Strength
High (suitable for panel mounting)

Locking Type
Threaded coupling (SO-239)

Cable Type
Compatible with RG-8, RG-58, RG-213 or similar cables

Number of Conductor
1 (center pin)

Core Material
Brass

Dielectiric Strength
Min. 1500V RMS at sea level

Usage & Applications
Ideal for radio communication, CB radio, RF devices, panel equipment

Diameter
Outer body ~16 mm

Conductor Type
Solid pin

Impedance
50 Ohm (nominal)

Conductor Shape
Round

Features
Right angled design, bulkhead for secure panel mounting, solder type for reliable connections, durable construction, corrosion resistant

Install Type
Panel Mount Bulkhead, right angle

Weight
Approx. 18 grams

Operating Temperature
-55C to +155C

Insulation
PTFE

Rated Temperature
-55C to +155C

Product Type
UHF Bulkhead Female Angled Solder Type Connector

Length
Standard, depends on panel thickness

Voltage
Up to 500V (typical for UHF connectors)

Insulation Material
PTFE (Polytetrafluoroethylene)

Application
RF communication, antennas, radio equipment, transmission lines, ham radio

Conductor Material
Brass (gold- or silver-plated contacts)

Jacket Material
Not Applicable (Connector only)

Storage Temperature
-55C to +155C

Connector Color
Silver

Shield Material
Nickel-plated brass

Jacket Color
Not Applicable (Connector only)

Dimension (L*W*H)
Approx. 33 x 18 x 18 mm

Color
Silver

Material
Nickel-plated brass, PTFE

Size
Standard UHF (SO-239) panel mount

Compliant Standards
RoHS compliant, industry standard

Gender
Female (SO-239)

Flange Shape
Square with mounting holes

Contact Resistance
Center 3m, Outer 2m

Corrosion Resistance
High, due to nickel plating

Insulation Resistance
>= 5000 M at 500V DC

Body Finish
Nickel-plated

Humidity Resistance
Up to 95% relative humidity

Resistant to Vibration
Yes

Contact Plating
Silver or gold plated for optimum conductivity

Frequency Range
DC to 300 MHz

Termination Method
Solder type for cable or wire

Mounting Type
Bulkhead, panel mount with securing hex nut

Durability
>500 mating cycles

Mating Connector
PL-259 (UHF male plug)

RoHS Compliance
Yes

Panel Hole Diameter
Approx. 16 mm

UHF Bulkhead Female Angled Solder Type For Panel Mount Trade Information

Minimum Order Quantity
5 Pieces

Main Domestic Market
All India

About UHF Bulkhead Female Angled Solder Type For Panel Mount

Description: UHF Connector, Female, Angled/90, Front Bulkhead, Panel Mount

Features:

UHF Connector, Female, Angled/90, Front Bulkhead, Panel Mount;
Designed for low frequency systems from 0.6-300MHz;
Threaded coupling mechanism is easy for assembly with high durability;
From the OEM Original Factory, same quality with much better price.

Appliance:

Antennas, Military, Public Address Systems and Low-frequency applications

Reliable and Durable Design

Crafted from nickel-plated brass and built for panel mounting, this UHF female connector ensures high durability and resistance against corrosion and environmental factors. Its right-angle form is suited for space-constrained setups requiring solid mechanical stability and more than 500 mating cycles.

Superior Connectivity and Performance

Featuring silver or gold-plated contacts, the connector delivers exceptional conductivity and minimal signal loss across a DC to 300 MHz frequency range. The low contact resistance and high insulation ratings enhance its suitability for demanding RF applications in both commercial and amateur contexts.

Versatile Application Range

Ideal for RF communication systems, ham radios, CB radios, and transmission lines, the angled bulkhead mount connector supports soldered connections for RG-8, RG-58, RG-213, and similar cables. Its compliance with industry standards, including RoHS, ensures dependable performance wherever employed.

FAQs of UHF Bulkhead Female Angled Solder Type For Panel Mount:

Q: How do I install the UHF Bulkhead Female Angled Solder Type connector on a panel?

A: To install, drill a panel hole approximately 16 mm in diameter, insert the connector through the hole, and secure it using the provided hex nut. Next, solder your cables center conductor and shielding to the designated points on the connector. Ensure the assembly is tight to maintain durability and optimal signal integrity.

Q: What types of cables are compatible with this connector?

A: This connector is compatible with standard RF cables such as RG-8, RG-58, RG-213, and other similar types. Its design focuses on compatibility with commonly used transmission lines in radio and communication equipment.

Q: When should I use a bulkhead panel mount UHF connector?

A: A bulkhead panel mount UHF connector is ideal when you need secure, vibration-resistant cable connections in RF equipment, such as in radio transmission lines, antenna panels, or enclosure-mounted devices, where durability and consistent signal quality are required.

Q: Where is this connector commonly used?

A: This connector is widely used in RF communication equipment, ham and CB radios, transmission line installations, and professional panel-mounted radio frequency applicationsboth for new designs and repairs.

Q: What are the key benefits of using the right-angled, bulkhead mount design?

A: The right-angled bulkhead design saves space in tight setups, provides mechanical stability through secure panel mounting, and enables easier cable routing. Its construction also ensures excellent resistance against corrosion, vibration, and harsh environments.

Q: How does the solder type termination enhance reliability?

A: Solder type termination ensures a direct, robust electrical connection between the cable and connector, minimizing signal loss and enhancing mechanical stability, especially in high-vibration or high-frequency environments.